Style Arc Estelle Cardigan – Minervacrafts Product Review

Hi all!

Can you remember back in February for Sew My Style that it was either the beautiful Rumana By Hand London Coat or Style Arcs Estelle Cardigan… I didn’t have the patience at the time to tackle such a big project so I decided to go for the cardigan!

My product review of the Pattern is now live over the Minervacrafts Blog.

So click on the link to find out just how easy it is to make your own!

Happy Sewing!

Sal

Xx

Sew Crafty Design Team Project #001 for 2018! Passport Holder Tutorial

16174536_1830206267254221_7090078855501172465_n

Hi All! I’m back for my 2nd year with The Sew Crafty Design Team and kicking off my 1st Project for 2018 showing you how to make your own Passport Cover! Honestly, It is really easy as i say it is!

List of Supplies:

Let’s make your Cover!

Fold the Fabric Right Sides Together.

I calculated for a UK Passport that i needed a rectangle of 31cm wide and 16cm high and includes a seam allowance of 1/4″ (o.6cm). It’s all written down in my Sew Crafty Journal, which is a fab tool as it had plenty of room to add my notes and calculations instead on a scrap piece of paper which i would end up losing!

I drew on the fabric using my tailors chalk and my Pattern ruler and tried my best to get it straight with the aid of the Ruler and my mat but i am only human after all!

Cut all the way around the fabric, following the outline we just drew.

Lay one piece of the Cover onto lightweight woven fusible interfacing. Pin and cut out one piece. I cheated a little, i folded my piece in half and then did the same for interfacing and pinned in place and cut out which meant less cutting! So now you should have 2 pieces of the fabric for your cover and 1 piece of interfacing 🙂

Sewing it all together!

Fuse the interfacing to the outer layer of the fabric with the glue side of the interfacing facing the wrong side of the fabric.

Place the two layers of fabric right sides together. Pin around the entire piece leaving a section about 2″ wide marked to be left unsewn for turning the piece right sides out.

Sew around the perimeter of the pieces using 1/4″ seam allowance starting at one side of the opening and remembering to Pivot (That word always reminds me of the episode of Friends with Ross and Chandler are moving the sofa to Ross’s apartment!!) when you reach each corner. Then back tacking at the otherside of the opening.

Trim the corners to reduce bulk. I trimmed at a 45-degree angle and also shaved off a little bit on either side of the corner to create nice corners.
Carefully turn the entire piece right sides out through the opening left in the bottom. Use a point turner or chopstick like i have to form nice corners after turning right side out.

Fold the seam allowance into the opening left in the bottom of the fabric and press the entire piece.

Now to finish the Cover!

Measure and fold each end of the fabric 2.1″ (6cm) into the inside. Pin in place all the way around the entire piece, and press.

Edge stitch the hole closed and the flaps in place all at the same time by stitching the perimeter of the cover at 1/4″ (0.6cm) seam allowance. Be sure to pivot at each corner. Press the entire piece after sewing.

Slip each end of your passport into the end flaps (hahaha!) sorry i am crude at times, and you’re ready to go!

So here is my lovely cover with 2 other covers!

20180311_181455

Of course the boys needed one a piece doing! Ethan went for Star Wars Darth Vadar Fabric and Rhys went for Spiderman Comic Fabric – which are both are currently on sale for £3 per half metre, bargain!!

Mr K had already bought himself one from Amazon so it saved me a job! So my fist lot of Holiday Sewing! Can’t believe it’s only 10 weeks away till we go away to Florida!! Best get a wiggle on on sewing my holiday wardrobe then!

Happy Sewing!

Sal xx

The Wearable Studio – The Franki Top

3a30d092-0696-4a72-8974-4bca7440c0a0

Hi All!

I was lucky enough to be selected by Melyssa for her 1st ever PDF Pattern to test! The Wearable Studio are a new Indie Pattern Company based in Australia and their patterns are designed to embody beauty, femininity, comfort and elegance.  Continue reading “The Wearable Studio – The Franki Top”

January’s #Sewmystyle Project and 1st of my #2018makenine complete!

Hi All!

Sorry I’ve been  missing in action… I’ve had the dreaded Cold/flu bug which knocked me for six and has taken me nearly a month to get over it!! So i am behind on my Blog and keeping you all updated on my Social Media but i am still here honest! Continue reading “January’s #Sewmystyle Project and 1st of my #2018makenine complete!”